harmony 鸿蒙Charging Type Customization

  • 2023-06-24
  • 浏览 (632)

Charging Type Customization

Overview

Introduction

By default, OpenHarmony supports multiple charging types. You can charge devices through different types of charging, for example, wired fast charging and wireless fast charging. OpenHarmony can display appropriate animations or take required service processing based on the charging type. However, the supported charging types vary according to products. To address this issue, OpenHarmony provides the charging type customization function.

Constraints

The configuration path for battery level customization is subject to the configuration policy. In this development guide, /vendor is used as an example of the configuration path. During actual development, you need to modify the customization path based on the product configuration policy.

How to Develop

Setting Up the Environment

Hardware requirements:

Development board running the standard system, for example, the DAYU200 or Hi3516D V300 open source suite.

Environment requirements:

For details about the requirements on the Linux environment, see Quick Start.

Getting Started with Development

The following uses DAYU200 as an example to illustrate charging type customization.

  1. Create the battery folder in the product directory /vendor/hihope/rk3568.

  2. Create a target folder by referring to the default folder of charging type configuration, and install it in //vendor/hihope/rk3568/battery. The content is as follows:

    profile
    ├── BUILD.gn
    ├── battery_config.json
    
  3. Write the custom battery_config.json file by referring to the battery_config.json file in the default folder of charging type configuration. For example:

    {
        "charger": {
            "type": {
                "path": "/data/service/el0/battery/charger_type"
            }
        }
    }
    
  4. Write the BUILD.gn file by referring to the BUILD.gn in the default folder of charging type configuration to pack the battery_config.json file to the //vendor/etc/battery directory. The configuration is as follows:

    import("//build/ohos.gni")                # Reference build/ohos.gni.
    
    
    ohos_prebuilt_etc("battery_config") {
        source = "battery_config.json"
        relative_install_dir = "battery"
        install_images = [ chipset_base_dir ] # Required configuration for installing the battery_config.json file in the vendor directory.
        part_name = "product_rk3568"          # Set part_name to product_rk3568 for subsequent build.
    }
    
  5. Add the build target to module_list in ohos.build in the /vendor/hihope/rk3568 directory. For example:

    {
    "parts": {
        "product_rk3568": {
        "module_list": [
            "//vendor/hihope/rk3568/default_app_config:default_app_config",
            "//vendor/hihope/rk3568/image_conf:custom_image_conf",
            "//vendor/hihope/rk3568/preinstall-config:preinstall-config",
            "//vendor/hihope/rk3568/resourceschedule:resourceschedule",
            "//vendor/hihope/rk3568/etc:product_etc_conf",
            "//vendor/hihope/rk3568/battery/profile:battery_config" # Add the configuration for building of battery_config.
        ]
        }
    },
    "subsystem": "product_hihope"
    }
    

    In the preceding code, //vendor/hihope/rk3568/battery/ is the folder path, profile is the folder name, and battery_config is the build target.

  6. Build the customized version by referring to Quick Start.

    ./build.sh --product-name rk3568 --ccache
    
  7. Burn the customized version to the DAYU200 development board.

Debugging and Verification

  1. After startup, run the following command to launch the shell command line:

    hdc shell
    
  2. Go to the custom battery level configuration directory. The path of DAYU200 is used as an example.

    cd /data/service/el0/battery/
    
  3. Modify the charging status, simulate reporting of the charging status, and check whether the displayed animation is correct. The following uses the default charging type and animation mapping as an example.

    1. Modify the charging type. echo 1 > charger_type
    2. Report the charging status change to trigger mapping between the charging type and animation. hidumper -s 3302 -a -r
    3. Check the output for the charging type. hidumper -s 3302 -a -i -------------------------------[ability]---------------------------- ------------------------------BatteryService------------------------ capacity: 11 batteryLevel: 4 chargingStatus: 1 healthState: 1 pluggedType: 2 voltage: 4123456 present: 0 technology: Li-ion nowCurrent: 1000 currentAverage: 1000 totalEnergy: 4000000 remainingEnergy: 4000000 remainingChargeTime: 0 temperature: 222 chargeType: 1 charger_type1

Reference

During development, you can refer to the default charging type configuration, as shown below:

```shell
{
    "charger": {
        "type": {
            "path": "/data/service/el0/battery/charger_type"
        }
    }
}
``` 

Packing path: /system/etc/battery

你可能感兴趣的鸿蒙文章

harmony 鸿蒙Subsystems

harmony 鸿蒙AI Framework Development Guide

harmony 鸿蒙NNRt Access Adaptation

harmony 鸿蒙Application Privilege Configuration

harmony 鸿蒙Development Example

harmony 鸿蒙Setting Up a Development Environment

harmony 鸿蒙Development Guidelines

harmony 鸿蒙Application Framework Overview

harmony 鸿蒙ArkCompiler Development

harmony 鸿蒙Custom Window Title Bar Development

0  赞